Advanced Test Equipment Rentals - Home Rentals - Sales - Service
Advanced Test Equipment Rentals
Toll Free: 1-800-404-ATEC (2832)
Follow ATEC on LinkedInFollow ATEC on YouTubeFollow ATEC on TwitterFollow ATEC on Facebook
Equipment > Amplifiers
Manufacturers > Amplifier Research

Amplifier Research 200T1G3 0.8-2.8GHz, 200W CW Pulse TWT Amplifier

Amplifier Research 200T1G3 CW TWT Amplifier, 0.8 GHz - 2.8 GHz

The Amplifier Research 200T1G3 0.8 GHz - 2.8 GHz, 200W CW Pulse TWT Amplifier is a 200 watt L-band traveling wave-tube amplifier (TWTA). The amplifier uses a 250 watt traveling-wave tube (TWT) to provide 200 watts minimum output over the TWT amplifier's full bandwidth. The amplifier is well suited for susceptibility and general laboratory testing where instantaneous bandwidth and high gain are required.

The Amplifier Research 200T1G3 0.8-2.8GHz, 200W CW Pulse TWT Amplifier is completely self-contained and packaged for standard 19-inch rack mounting or bench top use. The front panel of the rack mountable amplifier is 10.5 inches high, and the overall unit is 28.25 inches deep, excluding the rear-panel connectors. For bench top use, the amplifier is supplied in an enclosure with integral carrying handles.

Primary power is 190 - 260 Volts 50 - 60 Hz, single phase. An efficient switching power supply design provides minimum power consumption. A fast regulation control loop and a high degree of filtering ensure performance within specifications over a wide range of operating conditions. The amplifier is fully enclosed, and the lower panel of the rack mountable amplifier is interlocked to reduce the likelihood of accidental contact with high voltage.

Specifications

Power output cw at output connector: 200 Watts
minimum linear (at 1 dB compression): 100 Watts min.
Flatness ±5 dB from 1.0 - 2.0 GHz
± 12 dB from 0.8 - 2.8 GHz
Frequency response 0.8 - 2.8 GHz
Input for rated output 1.0 mW max.
Power Gain (at max. setting) 53 dB min.
Gain adjustment (continuous range) 35 dB min.
Input impedance 50 Ω, VSWR 2.0:1 max.
Output impedance 50 Ω, VSWR 2.5:1 typ.
Mismatch tolerance Output power foldback protection at reflected power exceeding 40 watts. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. May oscillate with unshielded open due to coupling to input. Should not be tested with connector off.
Modulation capability Will faithfully reproduce AM, FM or pulse modulation appearing on the input signal. AM peak envelope power limited to specified power.
Noise power density -72 dBm/Hz (max.)
-77 dBm/Hz (typ.)
Harmonic distortion -3 dBc max.
-6 dBc typ.
Primary power 190 - 260 Vac, 50/60 Hz single phase, 2.5 kVA max.
Connectors rf input (on rear panel): Type N female
rf ouput (on rear panel): type N female
rf output sample port (on rear panel): type N female
Cooling Forced air (self-contained fans, air entry and exit in rear)
Weight 68 kg. (150 lb.)
Dimensions (W x H x D) 50.3 x 29.7 x 76.2 cm (19.8 x 11.7 x 30 in.)
Please contact us for more information on the Amplifier Research 200T1G3 CW Pulse TWT Amplifier

Featured Test Equipment:

Rent an Haefely ECompact 4 Transient Immunity Test Set

Haefely ECOMPACT4
Transient Immunity Test

Voltech PM6000
Voltech PM6000
Power Analyzer



IFI T4026-40
TWT Amplifier

Varian 956 Porta Test
Teseq NSG 438
ESD Gun

Solar 2654-1
Solar 2654
Transient Generator
Forms Terms & Conditions Privacy Notice Home Page Terms of Use
Copyright © 1996-2010  |  Advanced Test Equipment Rentals  |  All Rights Reserved