 |
|
Keytek EMCPro Advanced EMC Test System for Compliance Testing
The answer to manufacturers’ demand for a mid-range, multi-capability EMC immunity tester, EMCPro® is easily configured to meet today’s immunity standards required for
CE Marking and compliance requirements. Operating via Thermo KeyTek’s easy to use Windows®-based PCsoftware or from the front panel, it enables test engineers and technicians to run compliance-level EMC immunity tests in accordance with European Norm requirements. Portable and low cost, the EMCPro® is ideal for companies who require flexibility, versatility, and the highest test level-to-cost ratio instrument on the market
Configurations for the Keytek EMCPro:
| Model PRO-SURGE |
| Surge per IEC 61000-4-5. Will do part of UL1449 |
| Voltage Waveform |
1.2/50µs |
| Peak Voltage |
250V - 6.6kV ±5%, 12Ω Mode |
| 250V - 6.0kV ±5%, 2Ω mode |
| Peak Current |
125 A - 3.3 kA ±10% |
| Additional 10 ohm Resistor |
Software selectable |
| Repetition Rate |
Up to 4 per minute |
| Open-circuit Voltage |
Front time: |
1.2µs ±30% |
| Duration: |
50µs ±20% |
| Undershoot: |
≤30% |
| Line sync accuracy |
±15%, 50 - 277 VAC |
| Model PRO-EFT |
| EFT per IEC 61000-4-4 and ANSI |
| Voltage Waveform |
5/50 ns ±30% |
| Peak Voltage |
250V - 4.4 kV ±5% |
| Burst Period |
300 ms ±10% |
| Burst Duration |
15 ms ±20% |
| Frequency |
1 kHz - 100 kHz in 0.5 kHz steps, ±10% |
| DC Blocking Capacitor |
10 nF (internal) |
| Model PRO-RING* |
| Surge Ring Wave per ANSI and UL. Will do part of 61000-4-12. |
| Voltage Waveform |
100 kHz damped cosine |
| Peak Voltage |
250 - 6.6kV ±5% |
| Repetition Rate |
<4/minute at 6 kV, faster at lower voltages |
| Open-circuit Voltage |
Rise Time: 0.5µs ±30% |
| Short-circuit Current |
Vp/Ip: 12 ohm ±3 ohm or 30 ohm ±8 ohm software selectable |
| *Pro-Telecom and Pro-Ring can not be installed together in the same unit |
| Surge Waveform Monitoring |
| Lines Monitored |
Monitors are automatically switched to match the generator coupling mode |
| Open-circuit Voltage |
1000:1 ±10% |
| Short-circuit Current Attenuation: |
200:1 ±7% |
| Model PRO-HPOWER |
| Power Frequency Magnetic Field per 61000-4-8 |
| Field Frequency |
50Hz/60Hz |
| Field Amplitude |
0.5-4A/m, in 0.25A steps, ±10% (with CM-HCOIL) up to 100A/m with the optional external HPOWER-EXT |
| AC Source |
Internal |
| Resolution |
0.25 Amp minimum |
| Coil Factor |
0.65 to 1.00 |
| Coil Resistance |
0.05Ω maximum |
| Model PRO-HPULSE |
| Pulse Magnetic Field per IEC 61000-4-9 |
| Field Pulse |
8/20µs |
| Field Amplitude |
100A/m -1000A/m, ±10% |
| Resolution |
5A/m |
| Coil Factor |
0.65 to 1.00 |
| Model PRO-PQF |
| Dips and Interrupts per IEC 61000-4-11 |
| Dips |
70%, 40% |
| Interrupts |
0% (short and open) |
| Transition Time |
1µs - 5µs |
| Inrush |
Minimum: |
250 Amps @ 100V - 120V |
| Minimum: |
50 0Amps @ 220V - 240V |
| AC Voltage |
50 VAC - 250 VAC, 50 Hz - 60 Hz |
| AC Current |
16A Max |
| PQF Sync Output |
5V signal occurs at each Dip or interrupt transition |
| Dip Duration |
10 msec min at 60 Hz |
| 2 msec min at 50 Hz |
| PQF Waveform Monitoring |
| Voltage Input Connection |
Fixed, L1 to L2 |
| Voltage Attenuation |
100:1 ±5% |
| Current Input Connection |
Fixed, L1 |
| Peak Current |
Minimum 500A inrush into 1700µF |
| Current Attenuation |
200:1 ±5% |
| Model PRO-BASE |
| System Voltage |
90 VAC - 240 VAC, 50 Hz - 60 Hz |
| Integrated EUT Mains Coupler/Decoupler |
AC Voltage: |
1 phase, 50-250VAC, 50/60Hz |
| AC Current: |
16A max |
| DC Voltage: |
100 VDC max |
| DC Current: |
10A max |
| Frequency: |
50/60Hz |
| EUT Connectors: |
Nema, British, Schuko |
| Control Interface: |
RS232 Fiber-optic |
| Safety Features: |
External Interlock for users
Interlock for CCL connector
External stop input |
|
