IFI PT-KW HP Series Pulse TWT Microwave Power Amplifiers

Rent IFI PT-KW HP Series Pulse TWT Microwave Power Amplifiers
Enlarge Image
Request Quote Print Page
Datasheet
The PT HP-series of KW High Power Pulse amplifiers built by IFI; are high power, “State-of-the-art” Pulse TWT amplifiers specifically designed for microwave testing applications. Our elegant approach provides up to 12,000 Watts of pulse power for various frequency ranges from 1.0 to 18.0 Gigahertz in various packages that offers all the controls and communications needed for today's automated test systems. These amplifiers have field proven reliability and unsurpassed performance as the best in the industry.

From the ground up the PT HP-Series amps are built to withstand rugged handling, whether it's being shipped to you or hauled around from site to site. Our amplifiers feature modular construction and this concept of modular design minimizes internally produced EMI signal leakage and provides easy access for field service and rapid turnaround at depot level repair facilities. Redundant thermal and airflow sensors prevent the TWT from overheating. In addition, high VSWR protection is built in.

The PT HP-Series “State-of-the-art” interface is sophisticated yet simple to use. The backlit LCD screen shows forward/reverse power indication, status and self-diagnostic information. All the amplifiers operating parameters are simultaneously available in the amplifier front panel display as well as over the remote bus. Selection switches allow you to switch the amplifier to the desired mode of operation for local control if the unit is not being operated remotely. For computer automation, both an RS-232 and IEEE-488 interface are included. To meet individual requirements, the PT HP-Series amplifiers can be easily customized with our available options that may be required for your application.

With all this capability and its reliable elegant design, the PT HP-Series amplifiers are the perfect amplifier for your testing needs.
 

IFI PT Features:

 
  • VSWR Reflected Power Protection, the unit operates without damage or oscillation into any magnitude of phase or load impedance, Open and Short Circuit Protection.
  • * Alternate Prime Power (specify at time of order)
  • GPIB IEEE 488 & RS232 Remote Control
  • RF Sample Port on the Front Panel, 112R for rear panel
  • Internal Pre-amplification to obtain rated output power with an input level of 0 dBm or less.
  • RF Input/Output Connectors on the Front Panel, 118R for rear panel
  • Internal Systems Diagnostics & Status Indicators
  • Filament/Beam Elapsed Time Metering in hours
  • RF Safety Interlock
  • Forward/Reflected Power Indication simultaneously on Front Panel display

 

IFI PT Specifications:

 
  • Input/output Impedance: 50 ohms
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Output Connector: Type SC or 716 Female up to 8 GHz, 8 – 12 GHz is WR90, 12 – 18 GHz is WR62, 7.5 – 18 GHz is WRD750, 6.5 – 18 GHz is WRD650. Other waveguides available by request or specification (see Option 117)
  • Input VSWR: 2.0:1
  • Output VSWR: 2.5:1
  • Pulse Input: BNC Female Front Panel {TTL into 50ohms standard}consult factory for special requirements
  • Pulse Width Range: 100 nsec – 100 usec
  • PRF Range: Up to 100 kHz Standard, Higher PRF ranges available consult factory
  • Duty Cycle: 6% Standard, Lower & Higher PRF ranges subject to TWT spec.
  • Rise & Fall Time: 15 ns nominal; 20 ns maximum
  • Pulse to Pulse Jitter: +/- 5 nsec maximum
  • Pulse Width Jitter:(Distortion) +/- 5 nsec maximum
  • Pulse Recovery Time: 150 nsec maximum
  • Pulse Delay: 250 nsec maximum / 180 nsec typical
  • Pulse Droop: 0.5 dB/100 usecs, 0.1 dB/10 usec
  • Power Output Stability: 0.2 dB Pulse to Pulse at constant drive level & PRF
  • Pulse On/Off Ratio: 80 dB
  • Phase Stability Pulse to Pulse: +/-1 degree nominal
  • Temperature: 0º to 50º C operating, -40º to 70º C non-operating
  • Humidity: 95% without condensation
  • Altitude: 10,000 feet operating, 50,000 non-operating
  • Cooling System: Air cooled, self contained
  • Modulation: All types, AM, FM, Pulse
  • Configuration: Rack Mount as specified in Model Table or Rack Integrated
  • Spurious Outputs: <-60 dBc nominal
  • Standard Prime Powers:
    100, 115, 120 VAC ±10% 50/60 Hz, single phase
    200, 220, 230, 240 VAC ±10% 50/60 Hz, single phase
    100/200VAC,115/208 or 200/220/230/240 VAC ±10% 50/60 Hz, three phase Wye or Delta and/or 400 Hz power is available.
    • Special Prime Powers other then listed are subject to availability
 
Model Number Frequency Range
(GHz)
Rated Power
(kW min.)
Gain
(dB min.)
Mains
(kVA)
Weight
(lbs.)
Size (Inches)
(W x D x H)
PT21-5KW 1.0 – 2.0 5.0 67 4.0 85 19 x 30 x 14
PT231-10KW 1.0 – 2.3 10.0 70 80 85 Rack Integrated
PT2719-6KW 1.9 – 2.7 6.0 60 2.5 85 19 x 25.25 x 14
PT42-5KW* 2.0 – 4.0 5.0 67 2.5 85 19 x 25.25 x 14
PT42-8KW 2.0 – 4.0 8.0 69 2.5 85 19 x 25.25 x 14
PT5727-4KW 2.7 – 5.7 4.0 60 2.5 85 19 x 25.25 x 14
PT64-6KW 4.0 – 6.0 6.0 68 2.5 85 19 x 25.25 x 14
PT84-5KW* 4.0 – 8.0 5.0 67 2.5 85 19 x 25.25 x 14
PT5653-8KW 5.35 – 5.65 8.0 68 2.5 85 19 x 25.25 x 14
PT115-1.75KW 5.0 – 11.0 1.75 63 2.5 85 19 x 25.25 x 14
PT128-5KW 8.0 – 12.0 5.0 67 2.5 85 19 x 25.25 x 14
PT9593-8KW 9.3 – 9.5 8.0 68 2.5 85 19 x 25.25 x 14
PT118-8KW 8.0 – 11.0 8.0 68 2.5 85 19 x 25.25 x 14
PT128-8KW 8.0 – 12.0 8.0 68 2.5 85 19 x 25.25 x 14
PT128-3KW 8.2 – 12.4 3.0 65 2.5 85 19 x 25.25 x 14
PT1087-4KW 8.7 – 10.5 4.0 66 2.5 85 19 x 25.25 x 14
PT1088-8KW 8.8 – 10.5 8.0 68 2.5 85 19 x 25.25 x 14
PT1088-8.5KW 8.8 – 10.5 8.5 68 2.5 85 19 x 25.25 x 14
PT109-8KW 9.0 – 10.0 8.0 68 2.5 85 19 x 25.25 x 14
PT1715-4KW 15.0 – 17.0 4.0 66 2.5 85 19 x 25.25 x 14
PT1812-3.5KW 12.0 – 18.0 3.5 66 1.5 85 19 x 25.25 x 14
*Over the majority of the band