EMC Partner CDN-A-8-200 Coupling-Decoupling Network | 1500 VDC , 200 A
- Multicolor LED coupling path indication
- Up to 1500 VDC EUT voltage
- Ready for EV and railway testing
Teseq CDN 3063-S100 3-Phase Coupling/Decoupling Network
- Three phase models with broad current range up to 100 A
- Fully automated surge and/or burst coupling
- IEC and ANSI coupling methods
Haefely FP-SURGE 100M2 Coupling/Decoupling Network for Surge
- Combination wave 1.2/50us - 8/20us
- Ring wave 100kHz
- 8kV impulse voltage
Haefely FP-COMB 63 Combined Automatic 3-Phase Coupling / Decoupling Network
- 0.2 – 5.0 kV ±10% at coaxial output
- 5 kV
- Up to 690 V AC | 50/60 Hz, 16, 7 Hz, DC
Haefely FP-COMB 32 Coupling/Decoupling Network
- Surge Combination Wave, 1.2/50us - 8/20us
- Ring Wave, 100kHz
- Electrical Fast Transient (EFT) / Burst
EMC Partner CDN UTP8 ED3 Coupling/Decoupling Network
EM Test ACC Automotive Coupling Clamp
- An automotive coupling clamp
- Constructed with precision
- Up to 40 mm diameter cables
Teseq CDN HSS-2 for Unshielded Symmetrical High Speed Communication Lines
- CDN for 1.2/50 μs pulse as per IEC 61000-4-5/Ed.3/77B/674A/CD:2012-05
- CDN for up to 8 wire unshielded twisted pair (UTP)
- Coupling to 1, 2 or 4 pairs
Teseq CDN 3083-B100 EFT/Burst Coupling/Decoupling Network
- 690 VAC, 1000 VDC
- Up to 8.8 kV burst pulses
- 100 A three-phase EFT / burst CDN
Teseq CDN 3083-S100 CDN | 3 Ph, 100 A, 690 V
- 100 Amps per phase with generous overload capacity
- For EUT power supplies up to 620 Volts
- Complies with IEC/EN 61000-4-5 and ANSI C62.45
Haefely PCD126A Telecom CDN
- Combination wave 1.2/50 us - 8/20 us impulse
- Serial resistor 40 Ohm included
- Up to 4 wires can be tested
Thermo Keytek CM-3CD-SRG 3 Phase Surge Coupler | 32A
- Semi-automatic operation when used with Thermo KeyTek’s CEMASTER or EMCPro simulators reduces the possibility of test sequence errors by prompting the user to make coupling mode selections
- Pre-programmed IEC test routines save time and decrease the potential for human error
- Ergonomic design provides maximum flexibility for operating from a table top or within a 19-inch rack.
Haefely IP4B Capacitive Coupling Clamp
- Designed as per IEC 61000-4-4 Edition 3
- EFT/Burst testing of signal and data lines
- For cable diameter from 4 – 40 mm
Teseq CDN 163 EFT / Burst Coupling Network
- 3-phase coupling network
- For AC and DC up to 100A per channel
- Short-term overstress capability
EMC Partner CN-EFT1000 Capacitive EFT/Burst Coupling Clamp
- Capacitive EFT/burst coupling clamp
- Complies with IEC 61000-4-4 EFT, IEC 61000-4-18, and ANSI C37.90.1 standards
- Used with the MIG Series
Teseq (Schaffner) KEMA 801A Decoupling Clamp
- Decoupling Network/ RF attenuation clamp
- As specified in IEC/EN 61000-4-6
- Very efficient coupling
Teseq CDN 500 ISO 7637-3 Capacitive Coupling Clamp
Teseq CDN USB/P Coupling/Decoupling Network
- Designed for IEC/EN 61000-4-6
- USB/p for test peripheral devices
Thermo Keytek CM-I/OCD CDN
- 4.4kV max surge voltage
- 200V Signal Line voltage
- 20V and 220V built-in clamps
Teseq CDN 118-M Telecom Line Coupling/Decoupling Network
- Telecom line surge testing
- Complies with IEC/EN 61000-4-5
EM Test Coupling NX7 BSR-3-480-32 CDN, 32A
- EM Test Coupling NX7 Series Automatic coupler for Burst and Surge Model with range selection 32, 63, 125 and 200 A Meet requirements for 3x690 VAC and 1,000 VDC LEDs indicate active
- Automatic coupler for Burst and Surge
- Model with range selection 32, 63, 125 and 200 A
Teseq CDN 3061 Automated 1-Phase Coupling/Decoupling Network
- Single phase model with exceeding current range
- Fully automated Surge and Burst coupling
- IEC and ANSI coupling
Teseq CDN 118 Telecom Line Coupling/Decoupling Network
- Telecom line surge testing
- Complies with IEC/EN 61000-4-5
EMC Partner CDN-A-8-32 Coupling-Decoupling Network
- Unique capabilities
- Excellent decoupling
- Highest EUT voltage supported
Thermo Keytek CM-3CD-EFT 3-Phase Coupler/Decoupler
- Operation is semi-automatic when used with EMCPro series test equipment, a personal computer, and the CEWare software, where the CEWare software can provide pauses and prompt the operator to change
- The over current protection of the CM-3CD-EFT includes detection of imbalanced phase-currents. When using the instrument with a one-phase load, a two phase load, or a load with extreme imbalance