EM Test EFT 500N8.1 EFT/Burst Generator, 7kV, 1MHz

Rent EM Test EFT 500N8.1 EFT/Burst Generator, 7kV, 1MHz
Enlarge Image
EM Test EFT 500N8.1
Request Quote Print Page
Datasheet
The EMTest EFT 500N8.1 EFT/Burst Generator is the state-of-the-art EFT/Burst tester with a built-in coupling/decoupling network for single phase or three-phase mains supply lines and a HV terminal to connect a capacitive coupling clamp.

The spike frequency can be varied from as low as 100Hz to 1,000kHz. The EFT 500N8.1 is capable to generate 1,000 spikes per second or up to 150 spikes per burst.

Its performance fully complies with IEC 61000-4-4:2004, IEC 61000-4-4 Amd.1 Ed.2:01/2010 and IEC 61000-4-4 Ed.3:03/2012. Pre-programmed Standard Test routines and a number of selected User Test routines make the EFT 500N8 an optimum standalone solution for both testing during development and final testing of products and sub-assemblies.
 

Features:

  • Standalone Tester
  • 7,000V Burst voltage
  • Spike frequency 1MHz
  • Built-in 1ph or 3ph coupler
  • USB (optical link) and GPIB interface
  • Standard Test routines
 

Specifications:

  • 3-phase coupler; 3 x 440V/32A
  • Test Level
    • Voltage range: 1,000V - 7,000V
    • Into 50ohm: 500V - 3,500V
    • Pulse shape: 5/50ns into 50ohm load
    • Rise time tr: 5ns ± 30%
    • Pulse width td: 50ns ± 30%
    • Pulse shape: 5/50ns into 1,000ohm load
    • Rise time tr: 5ns ± 30%
    • Pulse width td: 35ns to 150ns
    • Source impedance: 50ohm ± 20%
    • Polarity: Positive/negative
  • Trigger
    • Automatic: Automatic release of the bursts
    • Manual: Manual release of a single pulse
    • External: External release of a single pulse
    • Burst duration: Td = 0.1ms - 999.9ms
    • Burst repetition rate:
      • Tr = 10ms - 9,999ms/man
      • Tr <= 9,999ms => Auto Trigger
      • Tr > 9,999ms => Man Trigger
    • Spike frequency: f = 0.1kHz - 1,000kHz
    • Test duration:
      • T = 0:01 min - 99:59 min
      • T > 99:59 min - endless
  • Output
    • Direct :Via HV coax connector
    • Coupler: L, N and PE, all combinations
    • DUT supply AC: 250V/16A, 50/60Hz
    • DUT supply DC: 250V/10A
    • DUT supply: Other DUT supply voltages onrequest
    • CRO Trigger: 15V trigger signal for oscilloscope; burst duration and pulse frequency can be checked
Options:
  • HFK: Coupling clamp as per IEC 61000-4-4
  • ADA 800: SHV-Adapter for HFK connection
  • KW 50: 50ohm matching resistor for verification
  • KW 1000: 1,000ohm matching resistor for verification
  • 6dB: 6dB attenuator
  • CNI 503: Coupling/decoupling networks, 3x440V/32-63-100A
  • iec.control: Software to control the test, including standard library, test report facility and data conversion generator
  • CA EFT kit: Kit for burst pulse verification consisting of KW50, KW1000 and adapter for EUT port in a plastic case for storage