Amplifier Research 200S1G6 Microwave Solid State Amplifier 0.7 - 6.0 GHz, 200 W

Tech Support
(800) 404-2832

With Every
Rental

Worldwide
Delivery

Amplifier Research 200S1G6 Microwave Solid State Amplifier 0.7 - 6.0 GHz, 200 W

Larger

SKU: AMPL-200S1G6

Categories

Documents

Datasheet

The Amplifier Research 200S1G6 is a solid-state, Class A design, self-contained, air-cooled, broadband amplifier designed for applications where instantaneous bandwidth, high gain and linearity are required. Housed in a stylish contemporary cabinet, the unit is designed for benchtop use, but can be removed from the cabinet for immediate equipment rack mounting.

The 200S1G6, when used with a sweep generator, will provide a minimum of 200 watts of RF power. Included is a front panel gain control which permits the operator to conveniently set the desired output level. The 200S1G6 is protected from RF input overdrive by an RF input leveling circuit which controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0 dBm. The RF amplifier stages are protected from over-temperature by removing the DC voltage to them if an over-temperature condition occurs due to cooling blockage or fan failure. There is a digital display on the front panel to indicate the operate status and fault conditions if an over-temperature or power supply fault has occurred. The unit can be returned to operate when the condition has been cleared. All amplifier control functions and status indications are available remotely in GPIB/IEEE-488 format, RS-232 hardwire and fiber optic, USB, and Ethernet. The bus interface connector is located on the back panel and positive control of local or remote operation is assured by a Local/Remote switch on the front panel of the amplifier.

The low level of spurious signals and linearity of the Model 200S1G6 make it ideal for use as a driver amplifier in testing wireless and communication components and subsystems. It can be used as a test instrument covering multiple frequency bands and is suitable for a variety of communication technologies such as CDMA, W-CDMA, TDMA, GSM etc. It is also suitable for EMC Test applications where undistorted modulation envelopes are desired.

The export classification for this equipment is 3A001. These commodities, technology or software are controlled for export in accordance with the U.S. Export Administration Regulations. Diversion contrary to U.S. law is prohibited.

Specifications
Features
Applications
Options
Accessories
Standards
Videos

Rated output power:	200 watts minimum
Input for rated output:	1.0 milliwatt maximum
Power output @ 3dB compression:	Nominal: 220 watts; Minimum: 180 watt
Power output @ 1dB compression:	Nominal: 180 watts; Minimum: 160 watts
Flatness:	±1.0 dB typical, ±2.5 dB maximum
Frequency response:	0.7 - 6GHz instantaneously
Gain (at maximum setting):	54 dB minimum
Gain adjustment:	10 dB minimum
Input impedance:	50 ohms, VSWR 2.0:1 maximum
Output impedance:	50 ohms nominal

Model	RF Input	RF Output
200S1G6	Type N female, front	Type N female, front
200S1G6M1	Type N female, rear	Type N female, rear
200S1G6M2	Same as 200S1G6 with enclosure removed for rack mounting
200S1G6M3	Same as 200S1G6M1 with enclosure removed for rack mounting
200S1G6M4	Same as 200S1G6M2 with rack enclosure and casters
200S1G6M5	Same as 200S1G6M3 with rack enclosure and casters

Amplifier Research 200S1G6 Microwave Solid State Amplifier 0.7 - 6.0 GHz, 200 W

Model Configurations:

RELATED PRODUCTS