EM Test UCS 200N50 Automotive Transient Generator
- EFT/Burst: 25V – 1,000V ±10%
- 60V / 50A continuous, 100A @ 500 ms
- ISO 7637-2 Pulses 1, 2, 3A/3B, 6
AE Techron DSR 100-200 | Pulse 2B and 4
- 4-Quadrant – Can source and sink current.
- ±80V – DC supply for 12V to 48V systems; meets 80V surge requirements.
- 300 kHz Sine – DC ripple tests for all major standards.
EM Test LD 200N Load Dump Generator for ISO 7637
- Generates clipped load dump pulses (optional built-in module).
- Built-in 0.5 - 38 ohm source impedance, selectable in 0.1 ohm steps.
Hilo-Test CAR Test System 14
- Rise time variable 1 - 5µs.
- Vehicle voltages : 12V / 24V / 42V / 48V / 70V.
- Battery current: 50A / 100A / 200A.
EM Test PFM 200N100.1 Automotive Power Fail Simulator
- Switch for Power supply (100 A) and signal/data lines (2 A)
- Pulses E10 and E13 of the LV 124/LV 148 standard
- Bidirectional current direction
AE Techron 3110 Standards Waveform Generator
- Includes a large library of Automotive and Aviation Standards’ test routines--complete list available as Supplemental Document under Datasheet on left
- Drag and drop interface makes it easy to modify existing tests or build new waveform sequences
- Loop entire tests or test sections; repeat loops with increments of up to four variables
Hilo-Test CAR PG 2804 Load Dump Generator
- Load Dump Generator.
- Pulse #5 / Test A / Test B.
- Ri = 0.5 / 1 / 2 / 4 / 8 Ω
EM Test Autowave Arbitrary Generator
- Dual-Processor-Technology, 500kS/s sample rate
- 4-channel arbitrary generator
- 2-channel transient recorder
EM Test PFS 200N Series Automotive Power Fail Simulator
- Standalone test generator for voltage dips and interruptions
- Rise/fall time <1us
- Electronic short-circuit protection
Hilo-Test CAR-AWG 1200 Battery Simulator
- For electrical installation of vehicles
- Battery simulator
- Bandwidth DC-200kHz
Teseq NSG5200 Automotive Transient Test System
Teseq PA 5740 Power Amplifier/Battery Simulator
- Capacitive stability mode
- High bandwidth up to 180 kHz
- Fast slew rate
Schwarzbeck NNBL-8240
- Max Current: 800A
- Voltage (50/60Hz): 650V
- Impedance: 50µH + 5Ω || 50Ω ±20%
EM Test RCB 200N1 Transient Immunity Test Generator for FORD EMC-CS-2009.1
- Approved by Ford acc. to EMC-CS-2009.1 requirements
- Pulses CI 220: A1, A2-1, A2-2, C-1 and C-2
- Pulse CI 260: F
Teseq NSG 5071 Inducitive Switch Transient Test Circuit
- Designed in accordance to Ford standard EMC-CS-2009
- Transients disturbances CI 220 A and C pulses
- CI 260 waveform F
Teseq CDN 500 ISO 7637-3 Capacitive Coupling Clamp
LV 123 Automotive Component Testing System
EM Test Automotive Transient Emission Set 100 kHz - 125 MHz
- BS 200N100 - Electronic switch, 60V DC/100A: Volt.Drop <1.2V@100A, <0.2V@25A Peak voltage max. 1,000V Reverse-polarity/short-circuit protected
- Volt.Drop <1.2V@100A, <0.2V@25A
- Peak voltage max. 1,000V
EM Test VDS 200N30 Voltage Drop Simulator | 60 V, 30 A
- Voltage up to 60 V
- Current up to 30A
- Bipolar-amplifier models available
BOLAB 100-TS Series
- Frequency Range: DC – 1 MHz
- Output: 400 W – 18000 W
- For LV124 / VW80000, LV148, ISO 16750, ISO 7637, DIN 40839, and GS 95024
EM Test UCS 200N Automotive Transient Generator for ISO 7637
- Built-in EFT/Burst generator module
- Built-in Micropulse generator module (ISO 7637, JASO, SAE and NISSAN)
- Built-in coupling network 60V, up to 200A
Hilo-Test CAR-AWG 6000 Battery Simulator
- Batterie simulator
- Bandwidth DC-200kHz
- Signal Bandwith DC-1MHz (small signal -3dB)
EM Test LD 200N100 Load Dump Generator
- Built-in 100A coupler 60 V/100 A
- Built-in battery switch for 100A
- Generates Clipped Load Dump pulses
Teseq NSG 5600 Automotive Transient Generator
Bolab AN-ABCD-60 Artificial Network System | 1000 V, 60 A
- In accordance with LV123, ISO 21498, MBN 11123, VW 80300, and IEC 61851-23
- Liquid cooled for stable resistance temperature and constant ohmic value
- True continues current loading without derating, ideal for in-the-loop testing during the development stage of HV components