Haefely AXOS8 Compact Conducted Immunity Test System
- 0.2 – 5.0 kV ±10% at coaxial output
- 50 Ohms
- 5 ns ±30%
Haefely PSURGE 30.2 Surge Test System | 30 kV / 30 kA
- Up to 30 kV impulse voltage
- Up to 30 kA impulse current
- automatic polarity switching
EMC Partner IMU-MGE Conducted Immunity Test System
- Surge / CWG 4kV / 5 kV / 6kV / 8kV
- Ring Wave 6kV / 8kV
- EFT 4kV / 5kV / 6kV / 7kV
Haefely AXOS5 Compact Immunity Test System
- Easy to operate with manual and automated test modes, software assisted test preparation
- Pre-defined test routines and visual aided test setups
- Economic & efficient touch screen guarantees reduction of time and effort
EMC Partner IMU3000 Immunity Tester
- 7” Colour touch panel
- Rotary knob for navigation and data entry
- EPOS (EMC PARTNER Operating System) a new concept in graphical user interface
Teseq CDN 3063-S100 3-Phase Coupling/Decoupling Network
- Three phase models with broad current range up to 100 A
- Fully automated surge and/or burst coupling
- IEC and ANSI coupling methods
Haefely PSURGE 8000 Surge Platform Test System
- Built according to IEC/EN 61000-4-5 Ed. 1 & 2 and ANSI C62.41/45
- 1.2/50 µs open circuit up to 7.4 kV
- 8/20 µs short circuit up to 3.7 kA
M Precision Laboratories EMCPro PLUS EMC Test System
- Portable, mid-range EMC test system
- Resident capabilities for compliance testing to 6 IEC/EN standards
- Addresses ANSI/IEEE C62.41, ITU, ETSI, & UL 864 standards
Thermo Keytek ECAT E521
- AC CDN for single-phase lines to 480V, 32A
- Surge Repetition Rate 1 shot/30 seconds @ <=10kV 1 shot/minute @ >10kV
- Open-Circuit Voltage: 1.2/50µs, 200V to 20.2kV ±10%
Teseq NSG 3060 Transient Generator
- Modular, expandable system
- Surge voltage to 6.6 kV for overtesting
- Easy to use 7" color touch screen
EMC Partner IMU-MGS Conducted Immunity Generator
- One touch parameter editing in run state
- Impulse stability over long periods
- Intuitive multi touch graphical interface
EMC Partner IMU4000 Immunity Tester 4kV
Thermo Keytek ECAT E103 Control Center
- Virtual Front Panel™ retains key operating parameters during set up & testing
- Multi-level system interlock architecture provides maximum safety
- Single output port/instant mode switching
EM Test NX5 Multifunctional Test Generator
- Small transient generator with 7" color touch screen
- IEC 61000-4-4 | Burst testing, 5.5kV
- IEC 61000-4-5 | Surge testing, 5.0kV
Haefely / Bellcore 1089 Lightning Test System
- Full hybrid waveforms according to the lastest GR-1089 Core section 4
- 1st and 2nd level lightning surges
- Integrated automatic coupling for 2 and 4 wire telecom system
Haefely VTM 15000/05 Impulse Transformer For Isolation Testing
- 1.2/50μs voltage impulse
- Output amplitude up to 15kV (PSURGE 8000 & PIM 100)
- Output amplitude up to 14kV (AXOS 8)
Teseq NSG 3040 Transient Generator
- Surge voltage to 4.4 kV
- EFT/Burst to 4.8 kV/1 MHz
- EUT Supply: 1-Phase
EM Test VSURGE NX20
- Surge voltage up to 20 kV
- 11 different capacitance ranges selectable from 20 nF to 170 nF
- Compliant to IEC/EN 61730-1/2
EMC Partner EMCP-INS-1250 Impulse Surge Generator
- Operating V: 100-240V (50/60Hz) ±10%
- Output impedance: 40Ω
- Consumed VA: ON<150VA, standby<15VA
Teseq CDN3063-C32 Coupling/Decoupling Network
- 3-phase models with broad current range
- Fully automated surge and burst coupling
- IEC and ANSI coupling methods
Thermo Keytek ECAT E522
- AC CDN for three-phase lines to 480V, 32A/phase
- Surge Repetition Rate 1 shot/30 seconds @ <=10kV 1 shot/minute @ >10kV
- Open-Circuit Voltage: 1.2/50µs, 200V to 20.2kV ±10%
EM Test NX7 Multifunctional Test Generator
- Compact generator featuring 7" color touch screen
- IEC 61000-4-4 | EFT/Burst testing, 5.5 kV
- IEC 61000-4-5 | Surge wave/combination wave testing, 7.0 kV
EM Test UCS 500N5 Multifunctional EFT, Surge & Power Fail Generator
- Burst module (IEC/EN 61000-4-4) up to 5.5kV
- Surge module (IEC/EN 61000-4-5) up to 5kV
- TSurge module (IEC/EN 61000-4-5); optional
EM Test CSS 500N10 Surge Current Generator, 6 kV, 10 kA
- Wave Shape 8us/20us
- Output voltage (open circuit): 250V to 6,000V +/-10%, Step width 50V
- 250V to 6,000V +/-10%,
Noiseken LSS-F02 Series Lightning Surge Simulator
- Conforms to the IEC61000-4-5 standard
- "Output voltage 15kV, current 7500A" which can conduct breakdown resistibility test
- "50% reduction of the output interval" which can drastically reduce the test time
